Brooneye's build

Show off your caddy
User avatar
Shaw
Caddy Fan
Posts: 53
Joined: Sun Oct 21, 2018 5:08 pm
Engine size/power: 2.0 TDI (140bhp)
Location: Armadale, Scotland

Re: Brooneye's build

Post by Shaw »

Looking fantastic!!
User avatar
brooneye
Hyper Poster
Posts: 1488
Joined: Sun Jan 17, 2016 6:51 pm
Engine size/power: 1.8 20V Turbo

Re: Brooneye's build

Post by brooneye »

Cheers man, still got loads to do but the cost slowly mounts up


Sent from my iPhone using Tapatalk
User avatar
brooneye
Hyper Poster
Posts: 1488
Joined: Sun Jan 17, 2016 6:51 pm
Engine size/power: 1.8 20V Turbo

Re: Brooneye's build

Post by brooneye »

Picked the door inserts up today

Image

Image

Image

Just got to figure out how to get them back together now. Open to suggestions from people


Sent from my iPhone using Tapatalk
User avatar
Caddyluv
Hyper Poster
Posts: 4171
Joined: Sat Oct 14, 2017 5:11 pm
Engine size/power: 2.0 CR TDI (108bhp)

Re: Brooneye's build

Post by Caddyluv »

Are they not plastic welded?


Sent from my iPhone using Tapatalk
User avatar
brooneye
Hyper Poster
Posts: 1488
Joined: Sun Jan 17, 2016 6:51 pm
Engine size/power: 1.8 20V Turbo

Re: Brooneye's build

Post by brooneye »

They certainly are, but I don’t think there will be enough to get the tabs to melt over again. So I’m looking at a possible back up plan as nowt goes to plan when I start


Sent from my iPhone using Tapatalk
User avatar
Caddyluv
Hyper Poster
Posts: 4171
Joined: Sat Oct 14, 2017 5:11 pm
Engine size/power: 2.0 CR TDI (108bhp)

Re: Brooneye's build

Post by Caddyluv »

You got any old trim bits.


Sent from my iPhone using Tapatalk
User avatar
brooneye
Hyper Poster
Posts: 1488
Joined: Sun Jan 17, 2016 6:51 pm
Engine size/power: 1.8 20V Turbo

Brooneye's build

Post by brooneye »

Got a few bits and pieces, know where your going with that, but I don’t think some of the tabs are long enough. I’ll sharp know over the weekend


Sent from my iPhone using Tapatalk
User avatar
Caddyluv
Hyper Poster
Posts: 4171
Joined: Sat Oct 14, 2017 5:11 pm
Engine size/power: 2.0 CR TDI (108bhp)

Re: Brooneye's build

Post by Caddyluv »

Don’t need to be. You use as a guide the melt A to B then use a bit of trim to flood there area. Count to 5 and done. I recommend doing NORTH, SOUTH, EAST, WEST method. Do 1 bit so on. ImageImage


Sent from my iPhone using Tapatalk
User avatar
brooneye
Hyper Poster
Posts: 1488
Joined: Sun Jan 17, 2016 6:51 pm
Engine size/power: 1.8 20V Turbo

Re: Brooneye's build

Post by brooneye »

Cheers caddyluv, I’ll give it a bash over the weekend


Sent from my iPhone using Tapatalk
User avatar
Caddyluv
Hyper Poster
Posts: 4171
Joined: Sat Oct 14, 2017 5:11 pm
Engine size/power: 2.0 CR TDI (108bhp)

Re: Brooneye's build

Post by Caddyluv »

Image


Sent from my iPhone using Tapatalk
User avatar
Barbel330
Hyper Poster
Posts: 2134
Joined: Tue Dec 15, 2015 9:20 pm
Engine size/power: 1.6 CR TDI (102bhp)

Re: Brooneye's build

Post by Barbel330 »

They look good.

Could melt cable ties into it to build it up a bit if you've not got any other bits of plastic handy. Just check that the plastic in the cable tie melts into the plastic on the door trim by trying it on an inconspicuous area first.
Instagram: @y_5cuf
User avatar
brooneye
Hyper Poster
Posts: 1488
Joined: Sun Jan 17, 2016 6:51 pm
Engine size/power: 1.8 20V Turbo

Re: Brooneye's build

Post by brooneye »

They look nice


Sent from my iPhone using Tapatalk
User avatar
The polisher
200BHP+
Posts: 285
Joined: Thu Apr 12, 2018 9:36 pm
Engine size/power: 1.9 TDI (104bhp)
Location: Ireland
Contact:

Re: Brooneye's build

Post by The polisher »

Barbel330 wrote:They look good.

Could melt cable ties into it to build it up a bit if you've not got any other bits of plastic handy. Just check that the plastic in the cable tie melts into the plastic on the door trim by trying it on an inconspicuous area first.

Iv used cable ties melted to repair motorcycles fairings , very strong shouldn't have a problem with them


Sent from my iPhone using Tapatalk
Touran seats, Touran Console, Touran carpets, Touran Door cards, Spoiler, German Plates, RCD 330, carpeted and insulated, TDI Mats, Stance lowering Kit, VW Mk6 Steering wheel, T6 Steelies, Bargain Sunvisor, Bragan Roof Rails,Touran mirrors
Instagram:HG_Metal_Polishing_13
Facebook: HG Metal Polishing
www.hgmetalpolishing.com
Ireland :shock:
User avatar
brooneye
Hyper Poster
Posts: 1488
Joined: Sun Jan 17, 2016 6:51 pm
Engine size/power: 1.8 20V Turbo

Re: Brooneye's build

Post by brooneye »

Today I managed to get some coding done today thanks to Hutchysrs50. Coded in washer level sensor

Image

Footwell lights

Image

And cruise control, but for some reason that hasn’t worked. So a bit of research why and then a trip back to see him


Sent from my iPhone using Tapatalk
User avatar
Liam
Hyper Poster
Posts: 3161
Joined: Wed Nov 18, 2009 9:47 am
Engine size/power: 2.0 TDI (140bhp)
Location: Cavan

Re: Brooneye's build

Post by Liam »

love the door cards nicely done
2016 2.0 Tdi Mk4 Trendline caddy 160bhp
Remapped by Joe Power at TDR.ie www.tdr.ie
Build thread here
http://caddy2k.com/forum/viewtopic.php?t=34976
Post Reply