My EX BG VR6 3.2 build
- Sean1066
- Hyper Poster
- Posts: 2338
- Joined: Wed Oct 24, 2018 11:01 pm
- Engine size/power: 1.6 CR TDI (102bhp)
- Location: Newton abbot Devon
Re: My BG Caddy maxi build
Been doing a bit today got my slip ring module ready to go in to take my Mk7
MFSW
Burnt my finger on the soldering iron
Sent from my iPhone using Tapatalk
MFSW
Burnt my finger on the soldering iron
Sent from my iPhone using Tapatalk
Last edited by Sean1066 on Thu Aug 08, 2019 9:00 am, edited 1 time in total.
- Svenycaddylife
- 100BHP+
- Posts: 143
- Joined: Tue Jul 09, 2019 11:04 pm
- Engine size/power: 1.9 TDI (104bhp)
- Location: Tiverton
Re: My BG Caddy maxi build
Got my vents in
Sent from my ANE-LX1 using Tapatalk
Sent from my ANE-LX1 using Tapatalk
- Sean1066
- Hyper Poster
- Posts: 2338
- Joined: Wed Oct 24, 2018 11:01 pm
- Engine size/power: 1.6 CR TDI (102bhp)
- Location: Newton abbot Devon
Re: My BG Caddy maxi build
Very nice buddy.
The A3 vents look really nice on a caddy
The A3 vents look really nice on a caddy
- Svenycaddylife
- 100BHP+
- Posts: 143
- Joined: Tue Jul 09, 2019 11:04 pm
- Engine size/power: 1.9 TDI (104bhp)
- Location: Tiverton
Re: My BG Caddy maxi build
Just needs some thicker foam between the vent and ducting to make a snug fit
Sent from my ANE-LX1 using Tapatalk
Sent from my ANE-LX1 using Tapatalk
-
- Caddy2k Groupie
- Posts: 8
- Joined: Sun Jun 02, 2019 7:37 pm
- Engine size/power: 2.0 TDI (140bhp)
Re: My BG Caddy maxi build
What else have you done to get them to fit properly? I’ve seen a couple of pics where other people have fitted them but they don’t always look quite right.Svenycaddylife wrote: ↑Mon Aug 05, 2019 6:38 pm Just needs some thicker foam between the vent and ducting to make a snug fit
- Svenycaddylife
- 100BHP+
- Posts: 143
- Joined: Tue Jul 09, 2019 11:04 pm
- Engine size/power: 1.9 TDI (104bhp)
- Location: Tiverton
Re: My BG Caddy maxi build
The bottom of the dash needed small bit of plastic cut out that was it they are easy to get back out again
Sent from my ANE-LX1 using Tapatalk
Sent from my ANE-LX1 using Tapatalk
- Timson
- Caddy2k Groupie
- Posts: 33
- Joined: Fri Jul 19, 2019 8:53 am
Re: My BG Caddy maxi build
Nice work! I love this build, gives me a lot of inspiration for my own maxi.
-
- 100BHP+
- Posts: 102
- Joined: Mon Jul 30, 2018 9:29 am
- Engine size/power: 1.6 CR TDI (102bhp)
Re: My BG Caddy maxi build
Awesome thread, some really good inspiration for all us fellow BG van owners, keep us updated dude
Sent from my SM-G930F using Tapatalk
Sent from my SM-G930F using Tapatalk
- Svenycaddylife
- 100BHP+
- Posts: 143
- Joined: Tue Jul 09, 2019 11:04 pm
- Engine size/power: 1.9 TDI (104bhp)
- Location: Tiverton
Re: My BG Caddy maxi build
This is how much I cut out to give a snug fit the first one I cut a little to much but it still stays in the hole okBeardyginge wrote: What else have you done to get them to fit properly? I’ve seen a couple of pics where other people have fitted them but they don’t always look quite right.
Sent from my ANE-LX1 using Tapatalk
- Sean1066
- Hyper Poster
- Posts: 2338
- Joined: Wed Oct 24, 2018 11:01 pm
- Engine size/power: 1.6 CR TDI (102bhp)
- Location: Newton abbot Devon
Re: My BG Caddy maxi build
@Dan4da thank you for your nice comments
I always try and keep this build update.
@timson thank you for giving me the inspiration to keep on building. Hopefully you will start a build to inspire others.
I always try and keep this build update.
@timson thank you for giving me the inspiration to keep on building. Hopefully you will start a build to inspire others.
- Sean1066
- Hyper Poster
- Posts: 2338
- Joined: Wed Oct 24, 2018 11:01 pm
- Engine size/power: 1.6 CR TDI (102bhp)
- Location: Newton abbot Devon
Re: My BG Caddy maxi build
Well after a lot of headaches I have finally got my spacewalker module all wired up. Fitted in my caddy and got my Mk7 golf MFSW fitted and working.
Now I think that looks a lot better
Sent from my iPhone using Tapatalk
Now I think that looks a lot better
Sent from my iPhone using Tapatalk
- Svenycaddylife
- 100BHP+
- Posts: 143
- Joined: Tue Jul 09, 2019 11:04 pm
- Engine size/power: 1.9 TDI (104bhp)
- Location: Tiverton
Re: My BG Caddy maxi build
Looks epic
Sent from my ANE-LX1 using Tapatalk
Sent from my ANE-LX1 using Tapatalk
- Timson
- Caddy2k Groupie
- Posts: 33
- Joined: Fri Jul 19, 2019 8:53 am
Re: My BG Caddy maxi build
That steering wheel looks amazing! I would like cruise control too. Is it possible to change the steering wheel like you did and code in the cruise control to work? So instead of a cruise control stalk I mean. I would then choose a MFSW over a stalk kind for convenience and the fact that you can also control the radio, etc.
- Sean1066
- Hyper Poster
- Posts: 2338
- Joined: Wed Oct 24, 2018 11:01 pm
- Engine size/power: 1.6 CR TDI (102bhp)
- Location: Newton abbot Devon
Re: My BG Caddy maxi build
@timson
You will have to get a spacewalker module to do that.
Then you will have to do some soldering like I did
You will have to get a spacewalker module to do that.
Then you will have to do some soldering like I did
- Timson
- Caddy2k Groupie
- Posts: 33
- Joined: Fri Jul 19, 2019 8:53 am
Re: My BG Caddy maxi build
Are there no MFSW's that do not require soldering in order for the cruise control to work? Like MFSW's from other caddy's?