My EX BG VR6 3.2 build

Sean1066 · Post by **Sean1066** » Sun Aug 04, 2019 3:39 pm

Been doing a bit today got my slip ring module ready to go in to take my Mk7
MFSW

Burnt my finger on the soldering iron

Sent from my iPhone using Tapatalk

Svenycaddylife · Post by **Svenycaddylife** » Mon Aug 05, 2019 3:25 pm

Got my vents in

Sent from my ANE-LX1 using Tapatalk

Sean1066 · Post by **Sean1066** » Mon Aug 05, 2019 6:25 pm

Very nice buddy.
The A3 vents look really nice on a caddy

Svenycaddylife · Post by **Svenycaddylife** » Mon Aug 05, 2019 6:38 pm

Just needs some thicker foam between the vent and ducting to make a snug fit

Sent from my ANE-LX1 using Tapatalk

Beardyginge · Post by **Beardyginge** » Mon Aug 05, 2019 7:11 pm

Svenycaddylife wrote: ↑Mon Aug 05, 2019 6:38 pm Just needs some thicker foam between the vent and ducting to make a snug fit

What else have you done to get them to fit properly? I’ve seen a couple of pics where other people have fitted them but they don’t always look quite right.

Svenycaddylife · Post by **Svenycaddylife** » Mon Aug 05, 2019 7:31 pm

The bottom of the dash needed small bit of plastic cut out that was it they are easy to get back out again

Sent from my ANE-LX1 using Tapatalk

Timson · Post by **Timson** » Tue Aug 06, 2019 7:30 am

Nice work! I love this build, gives me a lot of inspiration for my own maxi.

Dan4da · Post by **Dan4da** » Tue Aug 06, 2019 11:14 am

Awesome thread, some really good inspiration for all us fellow BG van owners, keep us updated dude

Sent from my SM-G930F using Tapatalk

Svenycaddylife · Post by **Svenycaddylife** » Tue Aug 06, 2019 6:05 pm

Beardyginge wrote: What else have you done to get them to fit properly? I’ve seen a couple of pics where other people have fitted them but they don’t always look quite right.

This is how much I cut out to give a snug fit the first one I cut a little to much but it still stays in the hole ok

Sent from my ANE-LX1 using Tapatalk

Sean1066 · Post by **Sean1066** » Tue Aug 06, 2019 7:00 pm

@Dan4da thank you for your nice comments
I always try and keep this build update.
@timson thank you for giving me the inspiration to keep on building. Hopefully you will start a build to inspire others.

Sean1066 · Post by **Sean1066** » Tue Aug 06, 2019 7:08 pm

Well after a lot of headaches I have finally got my spacewalker module all wired up. Fitted in my caddy and got my Mk7 golf MFSW fitted and working.

Now I think that looks a lot better

Sent from my iPhone using Tapatalk

Svenycaddylife · Post by **Svenycaddylife** » Tue Aug 06, 2019 7:12 pm

Looks epic

Sent from my ANE-LX1 using Tapatalk

Timson · Post by **Timson** » Thu Aug 08, 2019 8:48 am

That steering wheel looks amazing! I would like cruise control too. Is it possible to change the steering wheel like you did and code in the cruise control to work? So instead of a cruise control stalk I mean. I would then choose a MFSW over a stalk kind for convenience and the fact that you can also control the radio, etc.

Sean1066 · Post by **Sean1066** » Thu Aug 08, 2019 8:59 am

@timson
You will have to get a spacewalker module to do that.
Then you will have to do some soldering like I did

Timson · Post by **Timson** » Thu Aug 08, 2019 9:13 am

Are there no MFSW's that do not require soldering in order for the cruise control to work? Like MFSW's from other caddy's?

CADDY2K.com

My EX BG VR6 3.2 build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build

Re: My BG Caddy maxi build