Toffee delights

brooneye · Post by **brooneye** » Sat Jul 20, 2019 8:54 pm

No used a leather type material and had loads of bubbles underneath and it started lifting before I even had a chance to put them back in

Sent from my iPhone using Tapatalk

caddychris2002 · Post by **caddychris2002** » Sun Jul 21, 2019 7:47 pm

Where did you get your suade from

Sent from my SM-G950F using Tapatalk

Post by **Lister79** » Sun Jul 21, 2019 8:15 pm

Hi mate, I got it from AS trims.

Sent from my iPhone using Tapatalk

caddychris2002 · Post by **caddychris2002** » Sun Jul 21, 2019 8:25 pm

Cheers lister vans looking sweet

Sent from my SM-G950F using Tapatalk

Post by **Lister79** » Sun Jul 21, 2019 8:26 pm

No worries, cheers mate.

Sent from my iPhone using Tapatalk

Post by **Lister79** » Tue Jul 23, 2019 5:55 pm

Got the glovebox/dash trims finished and put back in today. I’m really pleased with how it’s looking now.
Ive left the steering column cowl off as my new steering wheel and gear lever gaiter should be here tomorrow, so hopefully I’ll get them and the module (from Spacewalker) fit at the weekend.

Sent from my iPhone using Tapatalk

Hudson97 · Post by **Hudson97** » Tue Jul 23, 2019 7:36 pm

This looks so smart mate, really like it

Sent from my iPhone using Tapatalk

Post by **Lister79** » Tue Jul 23, 2019 8:02 pm

Cheers mate.

Sent from my iPhone using Tapatalk

Post by **Lister79** » Wed Jul 24, 2019 3:31 pm

Feels like Christmas

. Can’t wait to fit this.

Sent from my iPhone using Tapatalk

brooneye · Post by **brooneye** » Wed Jul 24, 2019 3:48 pm

Wow that’s nice

Sent from my iPhone using Tapatalk

BradleyB · Post by **BradleyB** » Wed Jul 24, 2019 10:50 pm

Looks nice lister

Sent from my iPhone using Tapatalk

Post by **Lister79** » Thu Jul 25, 2019 7:07 am

Well I couldn’t wait so stopped up well past my bed time to get it fitted.
Everything is working with the exception of the cruise as it appears to have a conflict (switches on/off but cluster display swaps between cruise and mileage when switched on). Hopefully it should just be something I’ve missed in the coding as the stalks have been changed to non cruise versions, however no faults were showing. Anyway I’ll have another look later as it was getting very late.

Wiring in the additional modules

All installed

Sent from my iPhone using Tapatalk

Post by **Lister79** » Thu Jul 25, 2019 6:27 pm

After seeing Dans Carbon struts thought I’d jump on the band wagon (not that my engine bay will ever be more than just a boring diesel, but hey

).

Total cost is £7.30 and takes about 10-15 minutes in total.

Links for parts and sizes I used:

Real Carbon tube 200mm length (22mm OD x 20mm ID)

https://rover.ebay.com/rover/0/0/0?mpre ... 3766189879

Ferrules (2 of 22mm ID required)

https://rover.ebay.com/rover/0/0/0?mpre ... 1802202012

Remove strut by releasing spring clips using a flat head screwdriver in slot (be careful they don’t fly off and get lost). Unscrew both ends. Measure tube and cut to size. Put strip of 3M tape around end then slide tube up from opposite end and ease over tape until central (you could also glue on). Drill a hole in the centre of each Ferrule to same size as boss on strut. Slide ferrule over each end (I put a small dot of glue on inner edge of Ferrule). Refit ends (with clips back in). Fit to car by simply pushing onto ball joint and enjoy for the whole 1 minute until you shut the bonnet

.

Sent from my iPhone using Tapatalk

Post by **Giddy** » Thu Jul 25, 2019 6:47 pm

Brilliant write up. Worth putting in "how to" section, so will be easy to find for everyone in the future.

Post by **Lister79** » Thu Jul 25, 2019 7:05 pm

Sent from my iPhone using Tapatalk

CADDY2K.com

Toffee delights

Re: Toffee delights

Re: Toffee delights

Re: Toffee delights

Re: Toffee delights

Re: Toffee delights

Toffee delights

Re: Toffee delights

Re: Toffee delights

Re: Toffee delights

Re: Toffee delights

Re: Toffee delights

Toffee delights

Re: Toffee delights

Re: Toffee delights

Re: Toffee delights