Stormtrooper caddy 4 build

the swan fiend · Post by **the swan fiend** » Tue Sep 08, 2020 10:43 pm

I love that. I really admire those that have the skills to break new ground. It looks brilliant. Well done gents

Sent from my iPhone using Tapatalk

Sean1066 · Post by **Sean1066** » Tue Sep 08, 2020 10:54 pm

That looks awesome Ryan.
Top work there buddy.

Grifnut · Post by **Grifnut** » Tue Sep 08, 2020 11:31 pm

Good work great idea !

Sent from my iPhone using Tapatalk

CwmurfNI · Post by **CwmurfNI** » Tue Sep 08, 2020 11:55 pm

Absolutely stunning

Post by **dan@biali** » Wed Sep 09, 2020 6:57 am

@Papa Bear I did look at using a router and even had my router table set up but the part is so curved at the ends when it passes through the bit it’s nowhere near touching but then does when you get to the flatter part. It was even missing the ends with the dremel setup. A custom guide bush for the bit is on order so will see if that works.

Looked so good as you drove off Ryan and my mums comment was it looks like it came like that which is praise indeed!

Papa Bear · Post by **Papa Bear** » Wed Sep 09, 2020 7:12 am

With wood I’d attach a baton on the back to use as a straight edge to run along the fence. Or could you run the opposite side in the fence?
Edit: just looked closely and with the double curve and the fact it’s not flat on the back for the number plate light trim, it would need some fancy baton but could work. Be easier in the side ones though.

Caddyluv · Post by **Caddyluv** » Wed Sep 09, 2020 8:29 am

Sent from my iPhone using Tapatalk

Papa Bear · Post by **Papa Bear** » Wed Sep 09, 2020 10:43 am

that really does look the mutts!

Caddyluv · Post by **Caddyluv** » Wed Sep 09, 2020 2:29 pm

What an afternoon social distance coffee can think up.

Sent from my iPhone using Tapatalk

Caddyluv · Post by **Caddyluv** » Thu Sep 10, 2020 5:38 pm

Went rattle hunting today. It’s been right behind me for about a week. Can’t cope. Think it’s the bolt on the compressor foot.

tightened up and a bit of lock tight

Sent from my iPhone using Tapatalk

Pepsi · Post by **Pepsi** » Fri Sep 11, 2020 9:14 am

The rear looks amazing. Live what you and Dan have come up with. Does look like it came like that.

james400 · Post by **james400** » Sat Sep 12, 2020 7:07 pm

Looks really good mate

Sent from my SM-G950F using Tapatalk

Peng · Post by **Peng** » Mon Sep 14, 2020 8:53 am

Read through this thread from start to finish in one go this weekend, really impressive build and you've done such a good job on it. Hoping my caddy can look even a fraction as good as yours

Caddyluv · Post by **Caddyluv** » Mon Sep 14, 2020 1:00 pm

Thank guys.

Sent from my iPhone using Tapatalk

Caddyluv · Post by **Caddyluv** » Tue Sep 22, 2020 2:00 pm

Done a couple of bits today after a very last min postponement.

Removed a deep scratch thanks to countywide scaffolding.

Then redone the black on the grab handle.

Sent from my iPhone using Tapatalk

CADDY2K.com

Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Re: Stormtrooper caddy 4 build

Stormtrooper caddy 4 build