If you don't cut the shaft down the golf knob won't clamp on properly as it doesn't go down far enough to reach the knurled part on the shifter shaft that holds it firmly in place
Sent from my SM-A725F using Tapatalk
NZ 1.2TSi Build
- Labern
- Caddy Fan
- Posts: 61
- Joined: Sun Mar 14, 2021 7:07 pm
- Engine size/power: 1.2 TSI (103bhp)
-
- 100BHP+
- Posts: 128
- Joined: Sun Dec 02, 2018 2:45 pm
- Engine size/power: 2.0 CR TDI (138bhp)
Re: NZ 1.2TSi Build
Wanted to buy a similar shift knob but I wasn't sure about the cutting , once you do it there is no turning back so I bought one that doesn't require cutting.
But is good to know the exact procedure, maybe I'll do it in the future. Thanks for sharing
But is good to know the exact procedure, maybe I'll do it in the future. Thanks for sharing
Current built thread: 2013 SWB Caddy 2.0TDI
viewtopic.php?f=13&t=48634
My previous built: 2007 SWB Caddy 1.9TDI
viewtopic.php?f=13&t=39945
viewtopic.php?f=13&t=48634
My previous built: 2007 SWB Caddy 1.9TDI
viewtopic.php?f=13&t=39945
-
- Caddy2k Groupie
- Posts: 13
- Joined: Thu Nov 11, 2021 12:48 pm
- Engine size/power: 1.6 CR TDI (75bhp)
Re: NZ 1.2TSi Build
Great to see a build from back home! And loving the blue theme. Are the Caddys popular in NZ? I'm in Aus now and haven't found many modded one here.
- Labern
- Caddy Fan
- Posts: 61
- Joined: Sun Mar 14, 2021 7:07 pm
- Engine size/power: 1.2 TSI (103bhp)
Re: NZ 1.2TSi Build
Thanks.
Nah not that popular. I only know of a couple of modded ones. One on this forum with VR6 engine swap.
Sent from my SM-A725F using Tapatalk
Nah not that popular. I only know of a couple of modded ones. One on this forum with VR6 engine swap.
Sent from my SM-A725F using Tapatalk
Last edited by Giddy on Thu Nov 18, 2021 9:14 am, edited 1 time in total.
Reason: Removed unnecessary quote of previous post
Reason: Removed unnecessary quote of previous post
- Labern
- Caddy Fan
- Posts: 61
- Joined: Sun Mar 14, 2021 7:07 pm
- Engine size/power: 1.2 TSI (103bhp)
Re: NZ 1.2TSi Build
I finished the back ages ago but never posted. I need to tidy up a couple of things though.
Sent from my SM-A725F using Tapatalk
Sent from my SM-A725F using Tapatalk
-
- Caddy2k Groupie
- Posts: 13
- Joined: Thu Nov 11, 2021 12:48 pm
- Engine size/power: 1.6 CR TDI (75bhp)
Re: NZ 1.2TSi Build
Looking good man. Here in Oz, just getting parts is a killer and when you finally find some, they are way over priced They never ever got the Touran here
- Labern
- Caddy Fan
- Posts: 61
- Joined: Sun Mar 14, 2021 7:07 pm
- Engine size/power: 1.2 TSI (103bhp)
Re: NZ 1.2TSi Build
Yeah that sucks, Oz missed out on so many cars.
I got my steering wheel off gum tree in Sydney for $120. So there are some cheap parts there haha.
I got some sent over from UK which cost way too much as I couldn't find stuff here.
Sent from my SM-A725F using Tapatalk
I got my steering wheel off gum tree in Sydney for $120. So there are some cheap parts there haha.
I got some sent over from UK which cost way too much as I couldn't find stuff here.
Sent from my SM-A725F using Tapatalk
Last edited by Giddy on Thu Nov 18, 2021 9:42 am, edited 1 time in total.
Reason: Removed unnecessary quote of previous post
Reason: Removed unnecessary quote of previous post
- TheGee
- 100BHP+
- Posts: 120
- Joined: Thu Sep 23, 2021 7:27 pm
- Engine size/power: 2.0 Stage 3+ TFSI
- Location: Kent
Re: NZ 1.2TSi Build
loving your work dude especially the led swap on the components! How difficult was it to do? I'm planning on swapping all mine out too but I'm not decided on a definite colour scheme yet
- Labern
- Caddy Fan
- Posts: 61
- Joined: Sun Mar 14, 2021 7:07 pm
- Engine size/power: 1.2 TSI (103bhp)
Re: NZ 1.2TSi Build
It's not too hard if you have a good soldering iron. The hardest is to get the aircon controls apart. The center dial takes a bit of effort to get off.
There are different Leds so you need to make sure each one has the same luminous intensity.
I got mine from RS Components
4 V Blue LED Side View SMD, Kingbright KA-4040QBS-D
4 V Blue LED PLCC 2 SMD, Kingbright KA-3528QBS-D
4 V Blue LED PLCC 2 SMD, Kingbright KA-2214QBS-D
Sent from my SM-A725F using Tapatalk
There are different Leds so you need to make sure each one has the same luminous intensity.
I got mine from RS Components
4 V Blue LED Side View SMD, Kingbright KA-4040QBS-D
4 V Blue LED PLCC 2 SMD, Kingbright KA-3528QBS-D
4 V Blue LED PLCC 2 SMD, Kingbright KA-2214QBS-D
Sent from my SM-A725F using Tapatalk
Last edited by Giddy on Thu Nov 18, 2021 10:16 pm, edited 1 time in total.
Reason: removed unnecessary quote of previous post
Reason: removed unnecessary quote of previous post
- TheGee
- 100BHP+
- Posts: 120
- Joined: Thu Sep 23, 2021 7:27 pm
- Engine size/power: 2.0 Stage 3+ TFSI
- Location: Kent
Re: NZ 1.2TSi Build
Thank you so much for the info I really appreciate it