Let the build begin - Plushed/Bagged VR6

Show off your caddy
User avatar
C Chis
Hyper Poster
Posts: 1645
Joined: Fri Mar 06, 2020 1:13 pm

Re: Let the build begin - Plushed VR6

Post by C Chis »

Looking to rub it down, treat the rust, etch prime and spray it India blue or perhaps finish with black gravitex, not sure yet.


Sent from my iPad using Tapatalk
2010 pre-facelift Mk3 3.2 VR6 : Touran Interior : 3D Premium Clocks : R32 Bumper : Climatic A/C

My VR6 Build Thread and Details can be Found Here
Skulirag
Caddy2k Groupie
Posts: 1
Joined: Tue Jan 23, 2024 7:45 pm

Re: Let the build begin - Plushed VR6

Post by Skulirag »

Thing looks sick!

Where are the secondary rubber seals from ?
User avatar
C Chis
Hyper Poster
Posts: 1645
Joined: Fri Mar 06, 2020 1:13 pm

Re: Let the build begin - Plushed VR6

Post by C Chis »

Hiya, cheers!

I bought one from eBay a while back the other was from LLL parts, both genuine VW Caddy door seals.

Cuts out a little noise but makes the doors sound so nice when closing!


Sent from my iPad using Tapatalk
2010 pre-facelift Mk3 3.2 VR6 : Touran Interior : 3D Premium Clocks : R32 Bumper : Climatic A/C

My VR6 Build Thread and Details can be Found Here
User avatar
C Chis
Hyper Poster
Posts: 1645
Joined: Fri Mar 06, 2020 1:13 pm

Let the build begin - Plushed/Bagged VR6

Post by C Chis »

Touran xenon headlights fitted this morning, straight forward enough. Halfway house for now (manual level adjustment) until I’ve tried them for a bit.

Image

Need to get rid of the moisture with some silica gel sachets to get rid of the moisture, downside of long term storage and fitting them on a cold, wet drizzly day Image

Image

Halfway house : removed the Touran stepper motors and replaced them with the original Caddy headlight height adjustment motors. Holding off on fitting the front and rear level sensors and the control module for automatic levelling until I’ve run them for a bit to make sure I’m happy with them.

Image
Original stepper motor on the way out

Image
Caddy motor installed with the original fittings, you’ve got to love VW for their multi use parts!

Additional wires run from the CECM to headlights to operate the Shutters for main beam, coding ticked and most importantly, no warning light on the instrument cluster and no flickering!

Going to swap out the H7 halogen lamps in a few weeks to try and match the colour temperature to the xenon’s.

Then… automatic levelling and headlight washers!


Sent from my iPad using Tapatalk
2010 pre-facelift Mk3 3.2 VR6 : Touran Interior : 3D Premium Clocks : R32 Bumper : Climatic A/C

My VR6 Build Thread and Details can be Found Here
Exterior6357
Caddy2k Groupie
Posts: 19
Joined: Mon Sep 30, 2024 2:40 pm
Engine size/power: 1.9 TDI (104bhp)

Re: Let the build begin - Plushed/Bagged VR6

Post by Exterior6357 »

Brilliant thread! Love a VR6, how does the caddy feel on full power? Sketchy or still planted enough?
mando
Caddy2k Groupie
Posts: 29
Joined: Tue Feb 28, 2012 11:46 pm
Engine size/power: 1.2 TSI (84bhp)

Re: Let the build begin - Plushed/Bagged VR6

Post by mando »

C Chis wrote:A quick picture at dusk, I’ll take some better ones over the weekend after I’ve cleaned the carpets, covered in muck and straw at the moment Image

Image


Sent from my iPad using Tapatalk
Hi mate, what are the 2 fixings where the old light was? Are they just caps?


Sent from my iPhone using Tapatalk
User avatar
C Chis
Hyper Poster
Posts: 1645
Joined: Fri Mar 06, 2020 1:13 pm

Re: Let the build begin - Plushed/Bagged VR6

Post by C Chis »

Exterior6357 wrote:Brilliant thread! Love a VR6, how does the caddy feel on full power? Sketchy or still planted enough?
Cheers! Thanks for taking the time to have a read through.

Planted when it’s dry, very, very sketchy from a standing start when it’s wet! ImageImage


Sent from my iPad using Tapatalk
2010 pre-facelift Mk3 3.2 VR6 : Touran Interior : 3D Premium Clocks : R32 Bumper : Climatic A/C

My VR6 Build Thread and Details can be Found Here
User avatar
C Chis
Hyper Poster
Posts: 1645
Joined: Fri Mar 06, 2020 1:13 pm

Let the build begin - Plushed/Bagged VR6

Post by C Chis »

[mention]mando [/mention]

Hi buddy, yes, just caps. The holes give access to the original fixing points for the shelf


Sent from my iPad using Tapatalk
2010 pre-facelift Mk3 3.2 VR6 : Touran Interior : 3D Premium Clocks : R32 Bumper : Climatic A/C

My VR6 Build Thread and Details can be Found Here
Slammedwhitecaddy
Caddy2k Groupie
Posts: 4
Joined: Sat Dec 21, 2024 11:23 pm
Engine size/power: 1.6 CR TDI (102bhp)

Re: Let the build begin - Plushed/Bagged VR6

Post by Slammedwhitecaddy »

Hi mate any chance you know what wires go to what on the rep in of the 4 button to 2 button switches
User avatar
C Chis
Hyper Poster
Posts: 1645
Joined: Fri Mar 06, 2020 1:13 pm

Re: Let the build begin - Plushed/Bagged VR6

Post by C Chis »

Yes, however it all depends on the year of your van, door module, etc…

There will also be details in the how to part of the forum, best to get your post count up and request an upgrade and check in there.


Sent from my iPad using Tapatalk
2010 pre-facelift Mk3 3.2 VR6 : Touran Interior : 3D Premium Clocks : R32 Bumper : Climatic A/C

My VR6 Build Thread and Details can be Found Here
User avatar
C Chis
Hyper Poster
Posts: 1645
Joined: Fri Mar 06, 2020 1:13 pm

Re: Let the build begin - Plushed/Bagged VR6

Post by C Chis »

So, it’s been a while…

Finally took the plunge and upgraded from my premium colour display to a digital display, straight forward job, old one out, stripped down to the pcb, installed into the back of the digital display with a very slight modification to the back right hand side of the dash cowling (to clear a small part of the new case).

Good fit in the Touran dash, no gaps, no issues setting up

Loving it!

Oh, and the warning lights were separate issues, now all sorted apart from the seat belt warning, this is new since upgrading to the digital cluster. I’ll sort that one out by wiring in the seatbelt switches.


Image
Image


Sent from my iPad using Tapatalk
2010 pre-facelift Mk3 3.2 VR6 : Touran Interior : 3D Premium Clocks : R32 Bumper : Climatic A/C

My VR6 Build Thread and Details can be Found Here
User avatar
Alex mc
200BHP+
Posts: 232
Joined: Tue Feb 23, 2021 12:36 pm
Engine size/power: 2.0 TDI (140bhp)
Location: Central Scotland

Re: Let the build begin - Plushed/Bagged VR6

Post by Alex mc »

Hi Colin the clocks look awesome do they make a diesel version of these .


Sent from my iPhone using Tapatalk
User avatar
C Chis
Hyper Poster
Posts: 1645
Joined: Fri Mar 06, 2020 1:13 pm

Re: Let the build begin - Plushed/Bagged VR6

Post by C Chis »

Hi Alex, yes, I believe so. I went from a diesel cluster to this one.

PM me if you want to see the dash in person and we can sort something out


Sent from my iPad using Tapatalk
2010 pre-facelift Mk3 3.2 VR6 : Touran Interior : 3D Premium Clocks : R32 Bumper : Climatic A/C

My VR6 Build Thread and Details can be Found Here
User avatar
gogsie
Twin Turbo poster
Posts: 388
Joined: Tue Mar 09, 2010 10:20 am
Engine size/power: 1.2 TSI (103bhp)
Location: Aberdeenshire

Re: Let the build begin - Plushed/Bagged VR6

Post by gogsie »

Alex mc wrote: Sun Feb 09, 2025 9:02 pm Hi Colin the clocks look awesome do they make a diesel version of these .


Sent from my iPhone using Tapatalk
I have these in my mk4 caddy and you can change the clocks to diesel rev/mph range in the settings.
Image
Post Reply