CADDY2K.com

Seat heating as the heated wheel works based on resistance. You will need to run a wire from drivers side seat plug and ground at the column.
You need to get mqb slipring from a car with heated wheel as it will have additional connection on spinning section for it.


Pic above is mine already done but you can see the extra plug connection on the lower left. That’s where the wheel plugs in.

Basically once you take apart the MQB slipring you will be using the front spinning plate + the surround cover + internal tape that’s inside it and install it into your slipring.

I will probably make a new thread about it with some pics for people to understand how I done it



Sent from my iPhone using Tapatalk

Awesome job! Wouldn’t mind a heated wheel.


Sent from my iPhone using Tapatalk

Heated wheels are very handy in the snow...


Sent from my iPhone using Tapatalk Pro

I keep thinking about this mod every morning when I try to peel my frozen hands from the steering wheel.

Hi, my names Tom, this I my first post was wondering if you could help I have a 2017 150 caddy and wan to fit acc and paddles I've got cruise as standard and the radar at the front and emergency braking so have ordered a 5ta steering wheel but could you give me the coding for channel 13 acc please, also I've enabled folding mirrors but would like to reduce the delay, I have vcds and vagcan pro thanks..

Regards tom.

Hi Tom I’ll post the coding later on for ya. I think you’ll need to get it calibrated as well. Not sure if it’s that straight forward to fit the ACC as I think it could be part of component protection so requires dealer tools


Sent from my iPhone using Tapatalk

Thanks very much for the reply, was hoping vagcan pro could help me but I could ask the dealer to do it then for me. Sorry but on the folding mirrors is that straight forward to adjust the delay when I press the button it takes a few seconds to retract once I press lock button thanks.

Tom.

My ACC coding is:

00001000FE0339

Regarding the delay...

I’m not gonna be held responsible if something goes wrong

09 central electrics
Security access
Login
Engineering mode
Up/download

Navigate to 1120,1121,1122
where first two numbers should be “14”
So 14XX 14XX 14XX
Change all three 14s to:

01 or 02 or 03 which stands for 0.1sec or 0.2 sec or 0.3 sec and so on.

01 is useless and possibly 02 might be too as this will also affect your windows opening closing so might make your windows go down a bit once you unlock the car.
Hope that helps!





Sent from my iPhone using Tapatalk

Absolutely brilliant, awesome many thanks.
Kind regards tom.

Hi Stan sorry to be a pain pal, steering wheel fitted to do acc retro fit but when I come to check the coding I found no coding table for engine ecu so struggling to code it this is my coding and just wondered if it differs from yours thanks. 011D00120445150090000 only I keep getting error 17149 check coding of ecus on power train data bus.

Kind regards tom.

what a van

shes a credit to you stan

Great build, love it!

Awesome build!

Where can i find this camera? Looks perfect!
Do you have a part number?

Thanks

stan-the-man wrote: ↑Sun Feb 25, 2018 3:07 pm My Ampire reverse camera failed few weeks ago.

Thanks lads!

The camera is this one:

https://www.ebay.co.uk/itm/232612589200





The footage quality is spot on in my opinion.


Sent from my iPhone using Tapatalk

stan-the-man wrote: ↑Sun May 06, 2018 9:39 am Thanks lads!

The camera is this one:

https://www.ebay.co.uk/itm/232612589200





The footage quality is spot on in my opinion.


Sent from my iPhone using Tapatalk

The picture look perfect! Thanks for the link, I will order the same one

What kind of cable did run up to the stereo?