CADDY2K.com

Got New Steering Control Module off MK6 MF Wheel fitted to my caddy today to match MK6 R Line Steering Wheel. Now recoded, all buttons except phone buttons work, these should work when have fiscom bluetooth fitted next week, Part. No.s are as follows:-

1KO 953 549 CH Mk6 MF Control Module

Slip Ring Must Be Version C or Higher

Code No. is 0000734

I had problems with the Yellow Steering Wheel light staying on but it was a matter of running through the basic settings again on VCDS and everything ok. My version was VCDS 912, I think you need at least this to code Mk6 Modules. Hope this information is of some use as their is a lot of doubt as to whether this can be done.

Have you been for a drive to reset it? Sometimes a short drive in a straight line sorts it out, other than that I've no idea.

Welcome.

Nice caddy

Few more changes made and hopefully on the home straight. (Pictures to follow!), K&N filter, decat & stainless steel back box. Painted engine cover & under bonnet soundproofing. Touran doorcards & centre console fitted & trimmed to match seats. (Thanks to brycieboy). Rear soundproofed, floor removed for rear footwells, rear seat belts in, roof liner on, and lots of carpeting. Just awaiting brackets for mounting rear seats, then carpet floor, a few power points installed (Thanks to daddy), then were done. (For Now) These are a moneypit & highly addictive!

Tim

good work m8 look forward to some pics

Look foward to seeing the van Tim I will give you a shout during the week , do you need an auxiliary fuse box and power cables run in By the sounds of things your finished in the back already dude your a fast worker. Look foward to your pics dude

DADDY wrote:Look foward to seeing the van Tim I will give you a shout during the week , do you need an auxiliary fuse box and power cables run in By the sounds of things your finished in the back already dude your a fast worker. Look foward to your pics dude

Yeah, will do, the front is almost finished apart from bluetooth, in the rear everythings near done but not really bolted together for the last time yet so will need cables etc in. At the last minute I also decided to put rear speakers in so waiting for them to come, gonna need to run speaker wire up as well and a couple of bits of the lighter plastic still to be painted dark grey for the rear interior. I'll give you a ring during the week to see how your fixed for the following week.
Cheers
Tim

tcc wrote: Yeah, will do, the front is almost finished apart from bluetooth, in the rear everythings near done but not really bolted together for the last time yet so will need cables etc in. At the last minute I also decided to put rear speakers in so waiting for them to come, gonna need to run speaker wire up as well and a couple of bits of the lighter plastic still to be painted dark grey for the rear interior. I'll give you a ring during the week to see how your fixed for the following week.
Cheers
Tim

Have you painted your side rail covers yet Tim.

Yes side rail covers painted, my rear spoiler cracked and someone scuffed a mirror cover so some bits will be getting painted again in a couple of weeks. My paint man has plenty of this colour left, (after all the s**t i've got done) so drop them bits of your's down and I'll get them painted at the same time. (No Charge), I give him a lot of work and he does my van very reasonable! Very unhappy when i put the touran door cards on that the door panel lights didn't work, but was on vag com today and reprogrammed module. Sorted

tcc wrote:Yes side rail covers painted, my rear spoiler cracked and someone scuffed a mirror cover so some bits will be getting painted again in a couple of weeks. My paint man has plenty of this colour left, (after all the s**t i've got done) so drop them bits of your's down and I'll get them painted at the same time. (No Charge), I give him a lot of work and he does my van very reasonable! Very unhappy when i put the touran door cards on that the door panel lights didn't work, but was on vag com today and reprogrammed module. Sorted

Nice one Tim, Tim did you read the post done by Matt @reflex, its about jointing the roof spoilers with metal pins to prevent cracking on single door installs, hope this helps.

Your doing a fine job Tim..... very impressed so far....... now lets see those pic's....

Oh and I'm from Ballymena too mate and I have never spotted your van around...... but then Im an old fart now so don't cruise as much......lol

tcc wrote:Few more changes made and hopefully on the home straight. (Pictures to follow!), K&N filter, decat & stainless steel back box.
Tim

Any problems with the decat or notice any change in the van since u did it ?

No, there were no problems after the decat. I done the decat, filter, and exhaust at the same time, there was a difference, a bit sharper, revving cleaner, turbo whistling so working better but I did these mods on my connect and noticed a big difference. Maybe I should have done it before I got it remapped. But all in all, yes it was a noticeable difference & worth doing Liam.

Tim

Any lights to be turned off after decat and is the decat easily available ?

No, didn't bring on any lights, don't think it was a big job, local Powerflow dealer had decat & back box done in a couple of hours. Only done the back box as its the size of your average dustbin and didn't think there was any need for it! Getting gases out quicker can only be a good thing

Tim